低成本、率、以工作质量保证产品质量

Inspection before use of internal combustion forklifts:

检查项目

Inspection items

（1）检查燃油，润滑油、液压油和冷却液是否加足（2）检查全车油、水有无渗漏现象

(1) Check if the fuel, lubricating oil, hydraulic oil, and coolant are fully filled (2) Check if there are any leaks in the entire vehicle's oil and water

（3）检查各仪表、信号、照明、开关、按钮及其他附属设备工作情况（4）检查发动机有无异，工作是否正常

(3) Check the operation of various instruments, signals, lighting, switches, buttons, and other auxiliary equipment (4) Check if the engine is normal and working properly

（5）检查转向，制动，轮胎和牵引装置的技术状况及紧固情况（6）检查起升机构，倾斜机构，叉架和液压传动系统的技术状况及紧固状况（7）检查随车工具及附件是否

(5) Check the technical condition and fastening of the steering, braking, tires, and traction devices (6) Check the technical condition and fastening of the lifting mechanism, tilt mechanism, fork frame, and hydraulic transmission system (7) Check whether the accompanying tools and accessories are safe

工作中检查项目：

Inspection items during work:

通常指在工作2h作用进行

Usually refers to working for 2 hours

检查项目

Inspection items

（1）检查发动机、底盘、工作装置、液压系统、仪表及信号装置的工作情况（2）检查轮轴、制动鼓、变速器、变矩器、齿轮泵和驱动桥温度是否正常（3）检查轮胎、转向和制动装置的状态和紧固情况（4）检查机油、冷却液、液压油的釉面高度和温度以及全车油、水有无渗漏现象内燃叉车回库后保养项目

(1) Check the operation of the engine, chassis, working devices, hydraulic system, instruments, and signaling devices (2) Check if the temperature of the wheel axles, brake drums, transmission, torque converter, gear pump, and drive axle is normal (3) Check the condition and fastening of the tires, steering, and braking devices (4) Check the glaze height and temperature of the oil, coolant, hydraulic oil, and the entire vehicle oil Maintenance items for internal combustion forklifts after returning to the warehouse for water leakage

检查项目

Inspection items

（1）清洁车辆

(1) Clean the vehicle

（2）添加燃油，检查润滑油、冷却液、液压油、液力油、北方冬季若未加防冻液或没有暖库应放进冷却液（3）检查V带的完好情况和松紧度

(2) Add fuel, check lubricating oil, coolant, hydraulic oil, hydraulic oil, and if antifreeze is not added or there is no warm storage in northern winter, coolant should be added. (3) Check the integrity and tightness of the V-belt

（4）检查轮胎气压

(4) Check tire pressure

（5）检查叉架、起重链拉紧螺栓的紧固情况

(5) Check the tightening of the tension bolts of the fork frame and lifting chain

（6）检查升降油罐、倾斜油缸、转向油缸和各管接头的渗漏情况（7）排除工作中发现的故障

(6) Check the leakage of the lifting oil tank, tilt oil cylinder, steering oil cylinder, and various pipe joints (7) Eliminate any faults found during operation

（8）检查、整理随车工具及附件

(8) Check and organize accompanying tools and accessories

（9）每工作40~50h应增加下列项目：清洗各空气滤清器；清洗蓄电池外部，检查电解液液面高度和电极柱、连接线的清洁、紧固情况；检查分电器触点，润滑分电器轴和凸轮；检查紧固全车各组成外部易松动的螺栓；对水泵轴承，转向节主销、横、直拉杆球头销，倾斜油罐横销，三联板中心销；对起重链条进行润滑和调整。

(9) The following items should be added every 40-50 hours of operation: clean each air filter; Clean the exterior of the battery, check the electrolyte level and the cleanliness and fastening of the electrode posts and connecting wires; Check the distributor contacts, lubricate the distributor shaft and cam; Check and tighten the bolts that are easily loose on the exterior of all components of the vehicle; For water pump bearings, steering knuckle main pins, horizontal and straight rod ball joint pins, inclined oil tank horizontal pins, and triple plate center pins; Lubrication and adjustment of the lifting chain.