低成本、率、以工作质量保证产品质量

合力叉车出车前的准备和检查工作完成与否非常的关键和重要，这关系到多方面的，下面济南合力叉车厂家为您解答。

Whether the preparation and inspection of Heli Forklift are completed is very critical and important, which is related to the safety of many aspects. Now, the manufacturer of Heli Forklift in Jinan will answer for you.

1、对车辆上班使用情况进行了解，交班人员应如实说明车辆的工作情况、目前状态。

1. Understand the use of vehicles at work, and the shift handover personnel shall truthfully explain the working conditions and current status of vehicles.

2、检查车辆外观有无磕碰情况，螺栓有无松动，玻璃是否完好，各零部件是否齐全，检查轮胎气压是否达到规定气压，轮胎是否损坏。

2. Check whether the vehicle appearance is bumped, whether the bolts are loose, whether the glass is intact, whether all parts are complete, whether the tire pressure reaches the specified pressure, and whether the tires are damaged.

3、轮胎磨损标准以目测是否露出胎线为准，小轮车拖斗轮胎磨损胎应少于8厘米。检查叉车门架\是否松动，如松动加以紧固；02门如变形可以进行校、油漆是否脱落，如脱落可以进行补刷油漆。

3. The tire wear standard shall be subject to the visual inspection to see if the tire line is exposed. The tire wear of the trolley trailer shall be less than 8 cm. Check whether the forklift mast is loose, and tighten it if it is loose; 02 If the door is deformed, it can be calibrated to see if the paint falls off. If it falls off, it can be repainted.

4、检查蓄电池接线桩柱是否牢固可靠。

4. Check whether the battery terminal posts are firm and reliable.

5、检查油、水、气是否有掺漏现象，检查水箱是否缺防冻液，检查时应注意车辆温度，观察水温表数值，温度超过50度时禁止打开水箱盖，以免发生喷溅事故。水箱添加防冻液的标准为防冻液液面在水箱盖下沿。

5. Check whether the oil, water and air are mixed with each other and whether the water tank is short of antifreeze. Pay attention to the vehicle temperature during the inspection. First observe the water temperature gauge value. Do not open the water tank cover when the temperature exceeds 50 degrees to avoid splashing accidents. The standard for adding antifreeze to the water tank is that the antifreeze level is at the lower edge of the water tank cover.

6、检查车辆机油有无渗漏、缺失情况，在检查之前叉车须静置十分钟以上，避免出现机油没有及时回流油箱导致油表数值不准确，检查机油尺时须确保油尺的清洁度，如右面低于油尺下方刻度线时需及时添加机油，添加量不许超过油尺上方刻度线。

6. Check whether the vehicle oil leaks or is missing. Before the inspection, the forklift must stand for more than ten minutes to avoid that the oil does not flow back to the tank in time, leading to inaccurate oil gauge values. When checking the oil dipstick, ensure the cleanliness of the oil dipstick. If the right side is lower than the scale line below the oil dipstick, add oil in a timely manner. The amount of oil added must not exceed the scale line above the oil dipstick.

7、查看车辆发动机皮带、风扇皮带、发电机皮带有无松动或磨损迹象，

7. Check whether the vehicle engine belt, fan belt and generator belt are loose or worn,

8、检查发动机有无漏油，各项轴承有无异常。

8. Check the engine for oil leakage and all bearings for abnormalities.

9、检查各仪表、开关、灯光、信号、雨刷器是否正常工作

9. Check whether all instruments, switches, lights, signals and wipers work normally

各项仪表正常后应当立即到发动机旁边在等待车辆预热的同时（预热不低于五分钟），如有问题应立即熄火，做进一步检查。更多相关内容就来我们网站http://www.jnhgjx.net咨询吧！

After all instruments are normal, go to the engine immediately and wait for the vehicle to warm up (not less than five minutes). If there is any problem, stop the engine immediately for further inspection. More relevant content will come to our website http://www.jnhgjx.net Consult!