低成本、率、以工作质量保证产品质量

This is very important because forklift batteries are a relatively fragile aspect, and if we do well in maintenance, it will extend their service life and lifespan. On the contrary, it will reduce work efficiency, accelerate battery loss, and ultimately prevent normal operation of the battery.

充电前的预备：电动叉车初步充电前查看电池温度，应低于30℃，电解液液面不低于隔板（如低于隔板，用蒸 馏水加注到挡板，然后查看导线功能。把电池充电插座（A衔接到充电器充电插头（B大将充电设备形状置于打开（ON方位。

Preparation before charging: Before the initial charging of the electric forklift, check the battery temperature, which should be below 30 ℃. The electrolyte level should not be lower than the partition (if lower than the partition, fill the partition with distilled water, and then check the wire function. Connect the battery charging socket (A) to the charger charging plug (B), and place the charging device shape in the ON position.

充电期间：电池温度不得逾越 45℃，如超出，中止充电，让电池冷却下来，然后以较低电流从头初步充电。

During charging: The temperature of the battery should not exceed 45 ℃. If it exceeds 45 ℃, stop charging, let the battery cool down, and then charge initially at a lower current.

充电结束：将充电器充电电流断开，“中止（STOP”灯亮。此刻，开关封闭，可从 充电器插头（B中拔掉电池插座（A。

Charging end: Disconnect the charging current of the charger, and the "STOP" light will be on. At this moment, the switch is closed, and the battery socket (A) can be unplugged from the charger plug (B).

电动叉车

Electric forklift 

正常充电能继续14～16小时，充电后各单体蓄电池的电解液密度应达到1.27～1.29kg/1.25℃；各大单体蓄电池的电压大约为2.7V。正确的做法是每个作业天后对电池进行再充电。

Normal charging can continue for 14-16 hours, and the electrolyte density of each individual battery after charging should reach 1.27-1.29kg/1.25 ℃; The voltage of each individual battery is approximately 2.7V. The correct approach is to recharge the battery after each homework day.

蓄电池充电进程的注意事项

Precautions for battery charging process

决不允许将电池露出给明火，构成的爆炸气体或许引起火灾

Never expose the battery to an open flame, as the explosive gas may cause a fire

充电应在通风良好的当地，打开上盖或将电池从叉车中取出

Charging should be done in a well ventilated area, with the upper cover opened or the battery removed from the forklift

决不能做临时接线或过错接线

Never make temporary or faulty wiring

接线端有必要张紧不得剥落，电缆绝缘有必要牢靠。

It is necessary to tension the terminals without peeling off, and the cable insulation must be firm.

电池要保持清洁、枯燥，用抗静电布去尘。

Keep the battery clean and dry, and use an anti-static cloth to remove dust.

不能在电池上放置工具或其它金属物体。

Do not place tools or other metal objects on the battery.

充电期间电解液的温度不得逾越45℃。

The temperature of the electrolyte during charging shall not exceed 45 ℃.

充电结束要查看电解液液面，应高出隔板15mm，正常情况下，一般一个星期补注一次蒸馏水。

After charging, check the electrolyte level, which should be 15mm higher than the partition. Normally, refill with distilled water once a week.

避免皮肤和酸液接触，一旦接触用很多肥皂水或请教医生。

Avoid contact with skin and acid. Once in contact, use plenty of soapy water or consult a doctor.

废旧电池应按当地有关规定处理。

Waste batteries should be disposed of in accordance with local regulations.

电动叉车电池更换与充电注意事项

Precautions for battery replacement and charging of electric forklifts

蓄电池替换方面，咱们要从以下四个方面加以注意。

In terms of battery replacement, we need to pay attention to the following four aspects.

拆掉电池固定螺钉

Remove the battery fixing screw

从电池接线端除去电缆。

Remove the cable from the battery terminal.

滑出或吊出电池。

Slide or lift out the battery.

按上面指示的逆进程安装电池，紧固并正确衔接。

Install the battery according to the reverse process indicated above, tighten and connect correctly.

本文由济南叉车租赁友情奉献.更多有关的知识请点http://www.jnhgjx.net真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated to the friendship of Jinan Forklift Rental. For more relevant knowledge, please click http://www.jnhgjx.net Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned