低成本、率、以工作质量保证产品质量

1、叉车出车前的保养：

1. Maintenance of forklifts before delivery:

检查机油、燃油、冷却水量是否足够，车辆各部分有无漏水、漏油和漏气的现象。检查轮胎、半轴、传动轴等处部件的螺栓、螺母是否紧固。检查转向机构各连接部位是否紧固可靠。

Check if the oil, fuel, and cooling water are sufficient, and if there are any water, oil, or air leaks in all parts of the vehicle. Check whether the bolts and nuts of the tire, axle shaft, transmission shaft and other parts are fastened. Check whether the connection parts of the steering mechanism are tightened and reliable.

检查轮胎气压是否符合规定标准。检查方向盘、离合器踏板的自由行程是否符合要求。检查刹车系统及驾驶系统。检查仪表、灯光、喇叭是否良好，察听发动机运转是否正常。

Check if the tire pressure meets the specified standards. Check if the free travel of the steering wheel and clutch pedal meets the requirements. Check the brake system and driving system. Check whether the instrument, light and horn are in good condition, and check whether the engine runs normally.

2、行驶中的保养：

2. Maintenance during driving:

济南叉车租赁厂家提醒您，行驶过程中，察听发动机及底盘各部位是否有异声响，并注意有无焦臭味。随时注意转向系统、制动系统的工作情况。观察各种仪表的工作是否正常。

Jinan forklift rental manufacturer reminds you that during driving, check the engine and chassis for any abnormal noises, and pay attention to any burnt odor. Always pay attention to the operation of the steering and braking systems. Observe whether various instruments work normally.

轮毂、制动毂、变速箱、差速器等有无过热现象。检视钢板弹簧有无断裂、松动或错位。检视转向机构各部连接是否紧固可靠。注意轮胎有无严重漏气、松摆现象或爆炸声响。行使途中停歇检查，检查车辆各部有无漏水、漏油或漏气现象

Check for overheating of the wheel hub, brake hub, gearbox, differential, etc. Inspect the steel plate spring for breakage, looseness, or misalignment. Check if the connections of all parts of the steering mechanism are tight and reliable. Pay attention to whether the tires have severe air leakage, looseness, or explosion noise. Stop and check during driving to see if there are any water, oil or gas leaks in all parts of the vehicle

3、收车后的保养：

3. Maintenance after receiving the vehicle:

清洁车辆内外各部。检查钢板弹簧有无断裂、松动或错位。检查各总成、部件的连接部位及挂装置等是否牢固可靠。检查有无漏油、漏水、漏气现象，并补充燃油、润滑油、制动液和蓄电池水。

Clean the interior and exterior of the vehicle. Check if the steel plate spring is broken, loose, or misaligned. Check whether the connection parts and hanging devices of each assembly and component are secure and reliable. Check for oil, water, and air leaks, and replenish fuel, lubricating oil, brake fluid, and battery water.

装用刮片式机油粗滤器的车辆，应以顺时针方向转动手柄23档。检查轮胎气压及外表，嵌入胎纹的杂物。放清储气筒内的积水和油污，并关好开关。检查冷却系统的情况，冬季在严寒地区要注意放水防冻。

Vehicles equipped with scraper type oil filters should rotate the handle clockwise for 23rd gear. Check the tire pressure and appearance, and remove any debris embedded in the tire tread. Clear the accumulated water and oil stains in the air storage tank and turn off the switch. Check the condition of the cooling system and pay attention to draining water to prevent freezing in severe cold areas during winter.

叉车的正常保养事项就从以上三个方面来了解到了，希望能够给您好的帮助，更多事项就来我们网站http://www.jnhgjx.net咨询看看吧！

We have learned about the normal maintenance of forklifts from the above three aspects. We hope to provide you with good help. For more information, please visit our website http://www.jnhgjx.net Consult and take a look!