低成本、率、以工作质量保证产品质量

叉车轮胎隶属于叉车配件中磨损大的配件，当磨损到了一定的程度的时候，将不能使用，需要更换。下面济南叉车维修厂家来讲讲叉车轮胎更换标准以及怎么更换的事项。

Forklift tires belong to the most worn parts of forklift accessories. When they are worn to a certain extent, they will not be used and need to be replaced. Next, Jinan Forklift Maintenance Factory will talk about the forklift tire replacement standard and how to replace it.

叉车轮胎更换标准:

Forklift tire replacement standard:

通常正常使用的叉车轮胎寿命是4、5年。因为胎面的橡胶会因时间久远而发生老化，过了5年即使胎纹的磨损很小也好换掉。而许多细小的裂纹正是造成爆胎的诱因。因为根据叉车轮胎橡胶配方的不同、用车环境和驾驶习惯的不同，叉车轮胎的使用寿命也会各不相同。

Generally, the service life of forklift tires in normal use is 4 or 5 years. Because the tread rubber will age over time, it is easy to replace it after 5 years even if the tread wear is small. Many small cracks are the inducement of tire blowout. Because the service life of forklift tires will vary according to the rubber formula of forklift tires, the vehicle environment and driving habits.

所以这就需要司机在平时开车多留些心，叉车轮胎老化也是有征兆的比方胎面老化的部位大都是从胎边或胎肩等边缘部位开始出现的临时的日晒雨淋会让橡胶表面出现成圈的小裂纹，这些裂纹标明此时叉车轮胎的承载力和品质都已经开始下降了为了降低爆胎风险好提前更换。

Therefore, drivers need to be more careful when driving at ordinary times. The aging of forklift tires also has signs. For example, the aging of tire tread is mainly caused by the temporary sun and rain from the edge of the tire edge or tire shoulder, which will make the rubber surface appear small cracks in circles. These cracks indicate that the bearing capacity and quality of forklift tires have begun to decline at this time. In order to reduce the risk of tire burst, it is better to replace them in advance.

除了会老化。以注明这条叉车轮胎的实时磨损状况。而对于没有磨损标志的叉车轮胎也可以用卡尺(或专用的叉车轮胎花纹尺)进行丈量，叉车轮胎也是要自然磨损的所以叉车公司的轮胎在出厂前都会在胎侧标注出磨损极限。

In addition to aging. To indicate the real-time wear condition of this forklift tire. Forklift tires without wear marks can also be measured with calipers (or special forklift tire pattern ruler). Forklift tires are also subject to natural wear, so the tire of forklift companies will be marked with wear limit on the tire side before delivery.

一般沟槽深度低于1.6毫米的叉车轮胎就不能再继续使用了因为此时叉车轮胎的排水性能和抗扎性能都会大幅下降。此外，如果一条叉车轮胎已经修补过三四次，那么叉车公司建议您好将这条叉车轮胎调换到非驱动轮或者后轮，以降低爆胎的风险。

Generally, forklift tires with a groove depth of less than 1.6 mm can no longer be used because the drainage performance and puncture resistance of forklift tires will be greatly reduced. In addition, if a forklift tire has been repaired three or four times, the forklift company recommends that you change this forklift tire to a non-drive wheel or rear wheel to reduce the risk of tire blowout.

叉车轮胎怎么换

How to change the forklift tire

1、将叉车停放在平坦、硬实的路面上，关闭发动机，使叉车处于空载状态。

1. Park the forklift on a flat and hard road, turn off the engine, and leave the forklift in an empty state.

2、叉子下降到地面，用停车制动装置止住车轮，如更换驱动轮胎，将千斤顶支承在车架前部侧面位置，如更换转向轮胎，将千斤顶支承在后桥后部托架。

2. Lower the fork to the ground and stop the wheel with the parking brake device. If the drive tire is replaced, support the jack at the front side of the frame. If the steering tire is replaced, support the jack at the center of the rear axle bracket.

3、用千斤顶稍稍顶起叉车，使轮胎仍和地面接触；先旋开固定充气管的螺栓，取下夹子，然后松开轮毂螺母。

3. Lift the forklift slightly with the jack to make the tire still contact with the ground; First unscrew the bolt fixing the inflation pipe, remove the clip, and then loosen the hub nut.

4、用千斤顶将车完全支起，旋下轮毂螺母，将轮胎拆下。

4. Use the jack to fully support the vehicle, unscrew the hub nut and remove the tire.

5、安装顺序与拆卸顺序相反。安装轮毂螺母时，紧固力矩必须达到规定值。

5. The installation sequence is the reverse of the removal sequence. When installing the hub nut, the tightening torque must reach the specified value.

安装完后要检查轮胎的充气是否达规定值，短距离运行一段后，再进行检查，看各部分螺栓是否。更多相关事项就来我们网站http://www.jnhgjx.net咨询！

After installation, check whether the inflation of the tire reaches the specified value. After a short run, check again to see whether the bolts of each part are correct. Come to our website for more relevant matters http://www.jnhgjx.net consulting service