低成本、率、以工作质量保证产品质量

In the transportation industry, forklift is a very important material handling equipment, the safety of its working state is very important. Forklift is very important for the new use of forklift. In some special cases, forklift leasing needs to pay attention to the following aspects:

对于新的叉车，他们需要经过严格的工厂检查。在叉车的租赁、储存和运输过程中，叉车的所有部件都有可能松动或损坏，因此在使用前要仔细检查叉车：检查叉车机械连接的限制，特别是转向系统、轮胎的限制和正确性，起升机构等场所；检查叉车发动机或直流电机的润滑情况，根据叉车润滑点加入足够的油、齿轮油、润滑油，检查各电气部件的接头、线路、照明是否完好、连接良好；检查胎压是否符合规定要求，工具、附件是否齐全。小编在此提醒您，在使用初期，零件的粗糙表面还没有完全抛光，因此加工后的形状与装配位置有一定的偏差，间隙与润滑条件之间会有一定的间隙。

For the new forklift, they need to go through strict factory inspection. In the process of leasing, storage and transportation of forklift, all parts of forklift may be loose or damaged. Therefore, carefully check the forklift before use: check the mechanical connection limit of forklift, especially the limitation and correctness of steering system and tire, lifting mechanism, etc.; check the lubrication of forklift engine or DC motor, and add enough oil according to the lubrication points of forklift Gear oil and lubricating oil, check whether the joints, lines and lighting of electrical components are in good condition and well connected; check whether the tire pressure meets the requirements, and whether the tools and accessories are complete. I would like to remind you that at the beginning of use, the rough surface of the parts has not been completely polished, so there is a certain deviation between the processed shape and the assembly position, and there will be a certain gap between the clearance and the lubrication conditions.
                 

铲车租赁，新的铲车是一定时期的磨合。一般来说，新叉车的磨合期为500。考虑到有些叉车没有里程表，磨合期也可以定为4个月或500小时，由于配合过紧，发动机的运动部件不能正常运动，磨合期需要调高一点。内燃机叉车应检查发动机和喷油泵中机油的质量和数量。磨合期结束后可换油一次。

Forklift rental, new forklift is a certain period of running in. Generally speaking, the running in period of new forklift is 500 km. Considering that some forklifts have no odometer, the running in period can also be set as 4 months or 500 hours. Due to the tight matching, the moving parts of the engine can not move normally, so the running in period needs to be adjusted higher. The internal combustion engine forklift truck should check the quality and quantity of oil in the engine and fuel injection pump. The oil can be changed once after the running in period.

一、经过培训并持有驾驶证的驾驶员可以驾驶；二、启动前检查所有控制和报警装置，如有损坏或缺陷，应在修复后运行；三、装卸过程中，货物不得超过规定的重量，货叉应完全插在货物下面，货物应均匀地放在货叉上，不得用单叉的尖部提货；四、在潮湿或平坦的道路上平稳地起动、转弯、行驶、制动和停车，并减速；在坡道上行驶时，请小心驾驶。在大于坡道十分之一的坡道上行驶时，上坡时向前行驶，下坡时向后行驶。上坡或下坡时不要转弯。叉车行驶时不得装卸；行车时注意行人、障碍物和坑洼，注意叉车上方的空隙；不得在驾驶员座椅以外的位置操作车辆和附件；对于起升高度大于3米的高门式叉车，应注意上方货物的下落，必要时应采取防护措施；工作时，应尽量使门架前后倾在小范围内；

1、 The driver who has been trained and holds a driver's license can drive; 2. Check all control and alarm devices before starting, if there is any damage or defect, it should be operated after repair; 3. During the loading and unloading process, the goods should not exceed the specified weight, the fork should be completely inserted under the goods, the goods should be evenly placed on the fork, and the tips of the single fork should not be used to pick up the goods; 4 Start, turn, drive, brake and stop smoothly on the smooth road, and slow down; drive carefully when driving on the ramp. When driving on a slope which is more than one tenth of the slope, it drives forward when going up the slope and backward when going down the slope. Don't turn when you go uphill or downhill. The forklift truck shall not be loaded and unloaded when driving; when driving, pay attention to pedestrians, obstacles and potholes, and pay attention to the gap above the forklift; do not operate vehicles and accessories outside the driver's seat; pay attention to the falling of the goods above and take protective measures when necessary; when working, try to make the gantry tilt forward and backward in a small range;