服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-新闻动态叉车的维修和保养工作应该如何做

叉车的维修和保养工作应该如何做

来源:https://www.jnhgjx.net/ 日期:2023-06-20 发布人:

一旦合力叉车出现了故障,则会影响到我们的正常搬运工作。要知道,济南合力叉车的存在是为了更好的解决仓库等地货物搬运的问题。如果我们不希望自己的叉车出现故障的话,那么日常的维护和保养工作都是不可少的。今天,小编来给大家说说日常的维护保养应该怎么做。
Once the Heli forklift malfunctions, it will affect our normal handling work. You should know that the existence of Jinan Heli forklift is to better solve the problem of cargo handling in warehouses and other places. If we don't want our forklift to malfunction, then daily maintenance and upkeep work is essential. Today, the editor will tell you how to do daily maintenance and upkeep.
1、检查渗漏情况,是:各管接头、制动泵、升降油缸、水箱,发动机、变速器、驱动桥、压转向器、转向油缸等。
1. Check for leakage, with the focus on: various pipe joints, brake pump, lifting cylinder, water tank, engine, transmission, drive axle, pressure steering gear, steering cylinder, etc.
2、轮胎气压检查:不足应补充规定值,确认不漏气。检查轮胎接地面和侧面有无破损,轮辋是否变形。
2. Tire pressure inspection: If there is insufficient, it should be replenished to the specified value to confirm that there is no air leakage. Check for damage to the tire ground and sides, as well as deformation of the wheels.
3、聚胺脂轮胎的检查:检查路面状况同,看轮胎是否有较大程度的磨损,安装有花纹的轮胎时,应注意车轮滚动方向的标记。
3. Inspection of polyurethane tires: Check the condition of the road surface to see if there is significant wear on the tires. When installing tires with patterns, pay attention to the marking of the rolling direction of the wheels.
4、制动液、水量检查:查看制动液是否在刻度范围内,并检查制动管路内是否混入空气。添加制动液时,防止灰尘、水混入。向水箱加水时,就使用清洁自来水,若使用了防冻液,应回流同样的防冻液。水温高于70度时,打开水箱盖,打开盖子时,垫一块薄布,不要带套拧水箱盖。
4. Brake fluid and water quantity inspection: Check whether the brake fluid is within the scale range and whether air is mixed in the brake pipeline. When adding brake fluid, prevent dust and water from getting mixed in. When adding water to the water tank, use clean tap water. If antifreeze is used, the same antifreeze should be returned. When the water temperature is above 70 degrees, open the water tank cover. When opening the cover, place a thin cloth on it and do not tighten the water tank cover with a sleeve.
济南合力叉车
5、合力叉车液压油、电解检查:先拨出机油标尺,擦净尺头后插入再拉出检查油位是否在两刻度线之间。工作油箱内油位应在两根刻度线之间;油太少,管路中会混入空气,太多会从盖板溢出。电瓶电解液也同样要处在上下刻度线之间,不足则要加蒸馏水到顶线。
5. Hydraulic oil and electrolytic inspection of Heli forklift: first pull out the oil dipstick, wipe off the head of the dipstick, insert and then pull out to check if the oil level is between the two graduation lines. The oil level in the working oil tank should be between two scale lines; If there is too little oil, air will be mixed in the pipeline, and too much will overflow from the cover plate. The electrolyte of the battery should also be between the upper and lower scale lines, and if it is insufficient, distilled water should be added to the top line.
6、制动跳板、微动踏板、手制动检查:踩下各踏板,检查是否有异常迟钝或卡阻。确认合力叉车手柄的可靠性。
6. Inspection of brake springboard, micro pedal, and hand brake: Press each pedal to check for any abnormal dullness or jamming. Confirm the safety and reliability of the handle of the Heli Forklift.
7、皮带、喇叭、灯光、仪表等检查:检查合力叉车皮带松紧度是否符合规定,没有调整余量或破损有裂纹,须更换;喇叭、灯光、仪表均应正常有效。
7. Inspection of belts, horns, lights, instruments, etc.: Check whether the tightness of the belt of the Heli Forklift meets the regulations, and if there is no adjustment allowance or damage or cracks, it must be replaced; The speakers, lights, and instruments should all be functioning normally and effectively.
8、蓄电池维护:合力叉车使用中应特别注意及时对蓄电池充电和蓄电池及维护,蓄电池充电时要注意方法,既要使蓄电池充足电,又不能造成蓄电池过量充电。发现电量不足时,应尽快充电,防止蓄电池过量放电。
8. Battery maintenance: During the use of Heli forklift, special attention should be paid to timely charging and maintenance of the battery. When charging the battery, attention should be paid to the method, which not only ensures that the battery is fully charged but also prevents overcharging. When the battery is found to be low, it should be charged as soon as possible to prevent excessive discharge of the battery.
9、辆运行中,切勿将“前进、倒退”的方向开关误当作转向开关。
9. During vehicle operation, do not mistake the "forward and reverse" direction switch for a steering switch.
10、放去机油滤清器沉淀物。
10. Remove the sediment from the oil filter.
11、查各部位的坚固情况,是:货叉架支承、起重链拉紧进修螺丝、车轮螺钉、车轮固定销、制动转向器螺钉。
11. Check the firmness of each part, with a focus on: fork support, lifting chain tension repair screws, wheel screws, wheel fixing pins, and brake steering gear screws.
12、检查转向器的可靠性、灵活性。
12. Check the reliability and flexibility of the steering gear.
13、清洗合力叉车上污垢、泥土和垢埃,部位是:货叉架及门架滑道、发电机及起动器、蓄电池电极叉水箱、空气滤清器。
13. Clean the dirt, soil, and debris on the Heli forklift, focusing on the fork frame and gantry slide, generator and starter, battery electrode fork water tank, and air filter.
我们在使用合力叉车的过程中,其实叉车的部件也在随着我们的不断使用,从而一直在不断的被磨损。如果我们去检查的话,可以很好的防止叉车在工作的过程中出现故障的。如果还有其他的问题,欢迎与我们http://www.jnhgjx.net联系。
During the process of using Heli forklifts, the components of the forklifts are also constantly being worn out as we continue to use them. If we go to inspect, it can effectively prevent forklifts from malfunctioning during operation. If you have any other questions, please feel free to contact us http://www.jnhgjx.net Contact.

济南韩工机械设备有限公司
地址:山东省济南市章丘区龙山街道济青路龙山段南侧1幢   电话:15953195999
网站:https://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  

鲁公网安备 37011202000702号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】