低成本、高效率、以工作质量保证产品质量

为了使叉车正常可靠地工作，应该在平常使用期间对其进行充足的了解，比如说先来了解下叉车起动性能良好的条件是什么。下面济南叉车租赁厂家为您解析。

In order to make the forklift work normally and reliably, it is necessary to fully understand it during normal use, for example, first understand the conditions for good starting performance of the forklift. Next, Jinan forklift rental manufacturer will analyze for you.

⑴要有足够的起动转速。起动转速高，缸内的气体渗漏量少，压缩空气向气缸壁传热的时间短，热量损失少，使压缩终了时的气体温度和压力得以提高。一般要求转速在100r/min以上。

⑴ Sufficient starting speed is required. High starting speed, less gas leakage in the cylinder, short time for compressed air to transfer heat to the cylinder wall, less heat loss, so that the gas temperature and pressure at the end of compression can be increased. Generally, the speed is required to be above 100r/min.

⑵气缸的密封性要好。这可进一步减少漏气量，保证压缩终了时气体有足够的燃烧温度和压力，气缸的压缩压力不得低于标准值的80%。

(2) The air cylinder shall have good sealing performance. This can further reduce air leakage, ensure that the gas has sufficient combustion temperature and pressure at the end of compression, and the compression pressure of the cylinder shall not be less than 80% of the standard value.

⑶要求发动机相对于运转机件之间的配合间隙适当，且润滑良好。

⑶ It is required that the fit clearance between the engine and the running parts is appropriate and the lubrication is good.

⑷蓄电池要有足够的起动电容量，且起动电路的技术状况正常。

(4) The battery shall have sufficient starting capacitance and the technical condition of the starting circuit shall be normal.

⑸起动油量符合规定，喷射质量良好，且喷油提前角要符合要求。

(5) The starting fuel quantity shall meet the requirements, the injection quality shall be good, and the injection advance angle shall meet the requirements.

⑹使用符合要求的燃料。

(6) Use qualified fuel.

此外固定的检查事项要做好，比如：检查调整气门间隙，检查节温器工作是否正常，检查多路换向阀、举升油缸、倾斜油缸、转向油缸、齿轮泵工作是否正常，检查变速器换挡是否正常，检查调整手、脚制动器刹车片与制动鼓的间隙，更换油底壳中的机油，检查曲轴箱通风管是否完好，清洗机油滤清器和柴油滤芯。

In addition, fixed inspection items should be done well, such as: check and adjust the valve clearance, check whether the thermostat works normally, check whether the multi way directional valve, lifting cylinder, tilt cylinder, steering cylinder and gear pump work normally, check whether the transmission shifts normally, check and adjust the clearance between the hand and foot brake pads and the brake drum, change the oil in the oil pan, check whether the crankcase ventilation pipe is intact, Clean the engine oil filter and diesel filter element.

对于新叉车或长期停用的叉车，在开始使用后两周内，在润滑该润滑的轴承时，应将旧油全部挤出，换上新油，润滑两次以上。更多相关的注意事项就来我们网站http://www.jnhgjx.net进行咨询吧！

For a new forklift or a forklift that has been out of service for a long time, the old oil shall be squeezed out and replaced with new oil for more than two times when lubricating the lubricated bearing within two weeks after use. More relevant precautions come to our website http://www.jnhgjx.net Consult!