全国服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-新闻动态-合力叉车电路维修之调节器的检查

合力叉车电路维修之调节器的检查

来源:https://www.jnhgjx.net/ 日期:2022-10-13 发布人:hangong

调节器(电压调节器)硅整流发电机中硅整流元件具有单向导电的性能,故可省去断流器。下面来讲讲济南合力叉车电路维修之调节器的检查内容吧。
Regulator (voltage regulator) The silicon rectifier element in the silicon rectifier generator has the performance of unidirectional conduction, so the cutout can be omitted. Now let's talk about the inspection contents of the regulator for circuit maintenance of Jinan Heli Forklift.
1、电压调节器铁心与触点臂间隙的调整。可借电压调节器活动触点和固定触点臂配合调整。其间隙一般为1.2~1.3mm,当电压过小,可增大其间隙,反之则减小间隙。也可调节电压调节器上的弹簧张力,即上下弯折弹簧钩,以改变弹簧张力。
1. Adjustment of the clearance between the iron core of the voltage regulator and the contact arm. It can be adjusted by means of the movable contact and fixed contact arm of the voltage regulator. The clearance is generally 1.2~1.3 mm. When the voltage is too small, the clearance can be increased, and vice versa. You can also adjust the spring tension on the voltage regulator, that is, bend the spring hook up and down to change the spring tension.
2、触点间隙的调整。触点间的压力是靠上下移动固定触点臂来进行调整的。触点应保持清洁平整,烧蚀时应用细砂纸打磨。
2. Adjustment of contact clearance. The pressure between the contacts is adjusted by moving the fixed contact arm up and down. The contact shall be kept clean and flat, and shall be polished with fine sandpaper during ablation.
在叉车维修调整触点间隙时,应注意电压调节器的固定触点和活动触点臂下扇触点的情况,因为会烧坏粘住,而引起发电机发电电压过高,而烧坏电气机件。
When maintaining and adjusting the contact clearance of the forklift, pay attention to the fixed contact of the voltage regulator and the lower leaf contact of the movable contact arm, because they will burn and stick, causing the generator to generate too high voltage and burning electrical components.
当电压过高时,应向下移动固定触点臂此时触点间隙0.3~0.5mm;当电压过低时,应提高固定触点臂。电阻烧坏或断路,应用同阻值的电阻更换。
When the voltage is too high, move the fixed contact arm downward. At this time, the contact clearance is 0.3~0.5mm; When the voltage is too low, raise the fixed contact arm. If the resistance is burnt out or open circuit, it shall be replaced with a resistance of the same value.
济南合力叉车
叉车转换开关控制线路由转换开关、接触器、电阻器及其他电器元件组成。其中,转换开关用于实现不同线路间的转换,但是,它不直接在线路间充当线路变换的角色,而是通过本身的不同挡位的触点的接触与断开,发布电命令,让对应的接触器产生动作,实现线路的变换。线路变换的目的,是为了导致直流串激电动机的转速变换,就是终实现蓄电池叉车的变速。
The control line of forklift transfer switch is composed of transfer switch, contactor, resistor and other electrical components. Among them, the transfer switch is used to realize the conversion between different lines. However, it does not directly act as the role of line conversion between lines. Instead, it issues electrical commands through the contact and disconnection of its contacts at different gears to make the corresponding contactors act to achieve line conversion. The purpose of the line transformation is to cause the speed transformation of the DC series motor, which is to finally realize the speed change of the battery forklift.
接触器是按照转换开关传来的电命令,利用叉车自身电磁铁的吸力,使自身通电触头接通或断开,以完成电路接通或断开的电器。接触器的电磁铁由转换开关中的不同挡位的触点的接触与断开来决定是否通电工作,而转换开关中的不同挡位的触点的接触与断开则由控制踏板来操控。
Contactors are electrical appliances that use the attraction of the forklift's own electromagnet to make their own energized contacts connected or disconnected according to the electrical command from the change-over switch to complete the circuit connection or disconnection. The electromagnet of the contactor determines whether it is powered on or not by the contact and disconnection of different gears in the change-over switch, while the contact and disconnection of different gears in the change-over switch are controlled by the control pedal.
采用接触器来完成电路的接通或断开,可以实现远距离的操控。3.转换开关也被称为主令控制器。这种控制器通过改变叉车电阻器不同阻值的介人与退出,综合采用调节电枢电压与调激磁电流的方式,对直流串激电动机进行调速。关注我们http://www.jnhgjx.net,了解更多相关事项!
Contactors are used to make or break the circuit, which can realize remote control. 3. The transfer switch is also called the master controller. This controller regulates the speed of DC series motor by changing the interposition and exit of different resistance values of forklift resistor, and comprehensively adjusting the armature voltage and exciting current. Follow us http://www.jnhgjx.net , learn more about it!

济南韩工机械设备有限公司
地址:山东省济南市章丘区龙山街道济青路龙山段南侧1幢   电话:15953195999
网站:https://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  技术支持:网站建设·推广运营

鲁公网安备 37011202000702号

 

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】