服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-新闻动态叉车的改进措施介绍!

叉车的改进措施介绍!

来源:https://www.jnhgjx.net/ 日期:2019-01-14 发布人:

  (1) 增加齿轮泵出口单稳分流阀管路的通径,由φ18mm加大到φ25mm,使油流在管内的流出速度由原来的10.3m/s降5.3m/s,大大减少了油液流经管路时的压力损失,同时降低了振动和噪声。

  (1) Increase the diameter of gear pump outlet to monostable distributor valve pipeline from 18 mm to 25 mm, so that the oil flow velocity in the pipeline decreases from 10.3 m/s to 5.3 m/s, which greatly reduces the pressure loss of oil flow through the pipeline, and reduces the vibration and noise.
  (2)在不改变车架整体结构的同时,将蓄电池箱向前移动,省出的空间用于增加油箱的容积,油箱的容量由原来的100L加大到150L:另一方面改变油箱的进出油口之间距离,由原来的300mm增加到800mm,确保了油液在油箱内能够得到充分的循环,不仅增加了油箱的散热面积,而且也改善了油箱的散热效果。
  (2) While not changing the overall structure of the frame, move the battery box forward and save space to increase the volume of the tank. The capacity of the tank is increased from 100L to 150L. On the other hand, the distance between the inlet and outlet of the tank is changed from 300mm to 800mm, which ensures that the oil can be fully circulated in the tank and not only increases the heat dissipation area of the tank. It also improves the heat dissipation effect of the fuel tank.
  (3) 将变矩器油散热器改作液压油散热器,设置在转向器回油油路中,其安装位置不变,由发动机风扇强制冷却。变矩器的散热采用安徽省凤阳水箱厂生产的油水合一散热器与发动机共同使用,安装在液压油散热器后面,位置与改动前一致;其水箱散热面积为22.5m2,油散热面积为6m2,确保发动机及变矩器油液的散热效果。
  (3) The oil radiator of the torque converter is replaced by a hydraulic oil radiator, which is installed in the oil return circuit of the steering gear. The installation position of the oil radiator remains unchanged and is forced to be cooled by the engine fan. The heat dissipation of the converter adopts the oil-water radiator produced by Fengyang Water Tank Factory in Anhui Province, which is installed behind the hydraulic oil radiator and is in the same position as before. The heat dissipation area of the water tank is 22.5m2 and the oil radiation area is 6m2, which ensures the heat dissipation effect of the engine and the oil of the converter.
济南二手叉车
  (4)改变转向液压缸的结构,采用QT40—10球墨铸铁导向套支承替代原导向套内的尼龙支承环,另增加一个斯特封密封件,同时将活塞支承环宽度由34mm改为28mm。
  (4) To change the structure of the steering cylinder, the Nylon bearing ring in the original guiding sleeve was replaced by the support of the QT40-10 ductile iron guiding sleeve, and a Stirling seal was added. At the same time, the width of the piston supporting ring was changed from 34 mm to 28 mm.
  改进后对系统进行检测,(1)对改进后的转向液压缸进行单元试验,把改进后的转向液压缸装在叉车转向桥体上将油液逐渐强制加热120℃以上,此时转向液压缸工作正常、无异响现象;(2)对整机液压系统压力损失进行测试,在无载工况下齿轮泵出口压力由原来的2.0MPa降1.5MPa,减少了液压系统的阻力损失和发热;(3)对整机按照平衡重式叉车整机实验方法/T3300—1992标准进行整机热平衡试验,整机运行1h 42min后液压油在接近90Y时趋于平衡,且发动机水温及变矩器油温均在正常工作温度范围内。
  After improvement, the system is tested. (1) Unit test is carried out on the improved steering hydraulic cylinder. The improved steering hydraulic cylinder is installed on the steering axle body of forklift truck and the oil is gradually forced to heat to more than 120 C. At this time, the steering hydraulic cylinder works normally and has no abnormal sound; (2) Pressure loss of the hydraulic system of the whole machine is tested, and the outlet pressure of gear pump is changed from the original under no load condition. 2.0 MPa is reduced to 1.5 MPa, which reduces the resistance loss and heat of the hydraulic system; (3) According to /T3300-1992 standard, the thermal balance test of the whole machine is carried out. After running for 1 hour and 42 minutes, the hydraulic oil tends to balance when approaching 90Y, and the water temperature of the engine and the oil temperature of the torque converter are within the normal working temperature range.
  以上内容由济南二手叉车厂家整理发布,更多相关内容可以点击我们的官网进行咨询:http://www.jnhgjx.net
  The above contents are arranged and published by Jinan used forklift manufacturers. More related contents can be consulted by clicking on our official website: http://www.jnhgjx.net.

济南韩工机械设备有限公司
地址:山东省济南市章丘区龙山街道济青路龙山段南侧1幢   电话:15953195999
网站:https://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  

鲁公网安备 37011202000702号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】