全国服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-常见问题-叉车叉取货物的正确操作步骤!

叉车叉取货物的正确操作步骤!

来源:http://www.jnhgjx.net/ 日期:2019-07-19 发布人:admin

  叉车准备前叉取货:需要调整叉臂间距。如果叉距过窄,货物很容易失去平衡,翻倒;如果叉距过宽,货物不易交叉或破碎。选择正确的叉形方向。

  Forklift truck ready fork pick-up: need to adjust the spacing of fork arm. If the fork spacing is too narrow, the goods are easy to lose balance and overturn; if the fork spacing is too wide, the goods are not easy to cross or break. Choose the correct fork direction.
  步是慢慢接近要叉车的货物,轻轻地刹车,使叉车停在货物前面。
  The first step is to approach the forklift slowly and brake gently so that the forklift stops in front of the goods.
  第二,将叉车的叉臂抬起到适当的高度,调整叉车的叉臂与地面平行。
  Secondly, raise the forklift arm of the forklift truck to a proper height and adjust the forklift arm of the forklift truck to be parallel to the ground.
  第三步,慢慢启动叉车,直到叉车臂完全进入叉车。此时,叉臂应与托盘平行,不要与托盘摩擦。
  The third step is to start the forklift slowly until the forklift arm fully enters the forklift. At this time, the fork arm should be parallel to the tray, not friction with the tray.
  第四,将货物抬起5-10厘米,检查货物的稳定性和分布是否均匀,防止货物翻滚。
  Fourthly, lift the cargo 5-10 cm to check the stability and distribution of the cargo, and prevent the cargo from rolling over.
济南二手叉车
  第五步:放慢速度,直到货物完全移开,否则不要侧移或转弯。
  Step 5: Slow down until the goods are completely removed, otherwise do not move sideways or turn.
  第六步:将货物靠在叉臂的后栅栏上,将叉臂举到离地15-20厘米的高度,在转向叉之前尽量倾斜门臂。
  Step 6: Place the cargo on the back fence of the fork arm, lift the fork arm 15-20 cm above the ground, and tilt the door arm as far as possible before turning the fork.
  取货时注意叉车:叉车抬起叉臂时,叉车应保持静止,除非正在调整位置;当货物被提升到较高的位置时,不要随意移动、旋转和倾斜叉臂,否则叉车可能翻倒。如货物可能落在天篷上,切勿堆放。
  When picking up goods, pay attention to forklift trucks: forklift trucks should remain stationary when lifting the forklift arm, unless the position is being adjusted; when goods are lifted to a higher position, do not move, rotate and tilt the forklift arm at will, otherwise the forklift truck may overturn. If the goods may fall on the canopy, do not pile them up.

济南韩工机械设备有限公司
地址:山东省济南市章丘区龙山街道办事处东3公里路北韩工叉车济南4S店   电话:15953195999
网站:http://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  技术支持:济南诺商

 

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】